GOST 8607-82 (ST SEV 3891-82) Group E83 STATE STANDARD OF THE USSR FOR LIGHTING FIXTURES residential and public buildings General specifications Luminaries for domestic and public interior lighting. General specifications OKP 34 6150 1934 6160 Effective date 01.01.1984 MEDIA INFORMATION 1. Developed and submitted by the Ministry of Electrical Industry of the USSR DEVELOPERS TN Siseykina (Leader), GS Sarychev, Dr. Sc. Sciences, BN Orlov, AV Ochkin; YB Eisenberg, Dr. Sc. Science; GN Undasynov, k.t.nauk 2. Approved and put into effect by Decision of the USSR State Committee on Standards of 09.11.82 N 4220 3. The standard is fully consistent ST SEV 3891-82 4. INSTEAD GOST 8607-74, GOST 11536-75 and GOST 14804-69 5. REFERENCE normative and technical documents Designation NTD, which was referenced paragraph number, sub-transfer, the application of GOST 2.601-68 2.2.2, 02/02/1913; 2.5.4, 3.2, 3.3, 3.5, 8.1 Standard 12.2.007.0-75 02.03 .1 GOST 7376-89 6.3.1.1; 6.3.2.1 GOST 7399-80 2.3.1, 02/04/1915; 04/02/1916 GOST 7933-89 6.3.1.1; 6.3.2.1 6.3.2.1 GOST 9142-90 GOST 10036-75 2.2.11; 6.3.1.1 6.3.1.1 GOST 10354-82 GOST 14254-80 GOST 15150-69 02.04.1915 2.4.1, 6.4; 6.5 GOST 17516-72 GOST 17557-88 2.4.3 2.4.9, 04/02/1910 GOST 17677-82 Chapeau, 1.1, 1.3, 2.2.1, 2.2.4, 2.2.8, 02.02.1910, 2.3.1, 2.4.2, 4/2/1915, 3.1, 4.1, 5.1, 6.1, 6.3, 7.1 GOST 21177-82 2.5.6 GOST 23216-78 6.3; 6.3.1.1; 6.4 GOST 23511-79 GOST 25516-82 2.5.6 02/04/1915 GOST 26092-84 Norms 15-78 2.5.6 04/02/1910 6. Validity extended until 1/1/1994 * Decree of the USSR State Standard 16.06.88 N 1843 _____________________ * Limiting the term of the removed protocol N 3-93 Interstate Council for Standardization, Metrology and Certification. (ICS N 5-6, 1993). 7. Reissue (September 1990) with variations in N 1, 2, 3, approved in October 1983 and September 1987, June 1988 (ICS 1-84, 12-87, 9-88) This standard applies to lamps with incandescent and discharge lamps for lighting of residential and public buildings which are produced by the economy and for export. The standard does not apply to lamps with individual power supplies, special medical, lighting and other theatrical scenes for photo, film and telesemok and television. Fixtures must meet the requirements of GOST 17677-82 and the requirements set forth in the relevant sections of this standard. (Revised edition, Alt. N 1, 2). 1. Classification 1.1. Classification fixtures - as per GOST 17677-82. 1.2. Classification of lamps for lighting of residential premises for the appointment is given in Table. 1. Table 1: Classification of lighting purpose lamps for general lighting (pendant, ceiling, wall, floor, table) for general lighting facilities Fixtures local lighting (table, floor, wall, pendant, is attached, built-in furniture) to ensure coverage of the working surface in accordance with the executed the visual work of the combined illumination lamps (pendant, wall, floor, table) have served as general lighting and local lighting, or both functions simultaneously Decorative lamps (table, wall) have served as an element of interior decoration lighting for orientation - nightlights (table, wall) To create the lighting necessary for orientation in a residential area in the nighttime lighting Spotlight (desktop, wall and is attached, recessed, ceiling, pendant, floor) to illuminate certain objects (Revised edition, Alt. N 1, 2). 1.3. Symbols of luminaries - as per GOST 17677-82. 2. SPECIFICATIONS 2.1. Lamps for residential premises shall be made in accordance with the requirements of this standard for technical documentation, duly approved. Fixtures for public buildings should be constructed in accordance with the requirements of this standard and technical requirements for specific types or groups of lamps to the technical documentation, duly approved. (Revised edition, Alt. N 2). 2.2. Light technical requirements 2.2.1. Light distribution class fixtures general, local and combined illumination of public premises should comply with GOST 17677-82 and indicated in the technical specifications for specific types or groups of fixtures. Type of curve intensity lamps for general lighting for public buildings should comply with GOST 17677-82 and indicated in the technical specifications for specific types or groups of fixtures. Light distribution class fixtures with incandescent and discharge lamps general, local and combined lighting of premises should comply with GOST 17677-82 and fitted visually to calculate the overall brightness. Type of curve intensity lamps for residential premises not specified. (Revised edition, Alt. N 1, 2). 2.2.2. Values ??protective corners and restricted areas of the local brightness lamps and combined lighting must comply with Table. 2 and the state: in any meridional plane - for Circular lamps; in the longitudinal and transverse, or only the transverse plane - for fixtures with two planes of symmetry. Table 2 Distance from the center of the light fixture to the floor, m Brightness limit area protective (or defensive conditioned) angle, at least in the lower hemisphere in the upper hemisphere to 1,1 inclusive. 85-125 ° 5 ° 35 ° St. 1,1 to 1.2 incl. 75-110 ° 15 ° 20 ° "1,2" 1,3 "65-95 ° 25 ° 5 °" 1,3 60-90 ° 30 ° - Notes: 1. The distance from the center of the light to the floor should be indicated in the operational document in accordance with GOST 2.601-68 lamps for residential premises, in the technical specifications for specific types or groups of fixtures - for public space, with distance from the optical center to the floor of mobile lighting fixtures for residential premises should be equal to the maximum allowable design in the position of lamps. 2. The bulb lights (except bulbs with mirrored dome of the bulb, decorative bulb and compact fluorescent lamps) should not extend beyond the plane of the upper or lower edge of the outlet of a lens or reflector. (Revised edition, Alt. N 1, 2, 3). 2.2.3. Values ??protective corners with night-light bulbs must meet the Table. 3. Table 3: How to install the lamp protective (or defensive conditioned) angle, at least in the lower hemisphere in the upper hemisphere Desktop 10 ° 90 ° Wall 30 ° (Revised edition, Alt. N 2). 2.2.4. Values ??protective corners and restricted areas of brightness lamps for general lighting public spaces in the lower hemisphere must comply with those in Table. 4 for the outboard, ceiling fixtures and built-in table. 5 - for wall and floor lamps. Table 4 Group rooms * Security (or conditional security), the angle in the transverse and longitudinal planes, at least Brightness limit area overall brightness, cd/m2, no more classes for light distribution according to GOST 17677-82 H P * In _________________________ Group premises are in a background application. January 1990 ° 0-90 ° 2000 2 2500 3000 3500 3 30 ° 60-90 ° 4500 5000 3500 * __________________________ * For ceiling and built-in lighting - no more than 5000 cd/m2. April 1990 ° 0-90 ° 4000 5000 5000 May 30 ° 60-90 ° 4500 * 5000 * __________________________ For ceilings and built-in lighting - no more than 5000 cd/m2. Table 5: How to install a light fixture Distance center lamp, m Protective (or contingent protection) angles in the transverse and longitudinal planes, at least Brightness limit area on the floor of the base area in the lower hemisphere in the upper hemisphere wall to 1.8 incl. - 30 ° 30 ° 60-120 ° St. 1,8 - 60-90 ° Floor Up to 1.0 incl. 10 ° 40 ° 80-130 ° from 1,0 to 1,3 inclusive. 20 ° 30 ° 70-120 ° St. 1,3 to 1.6 incl. 30 ° 20 ° 60-110 ° St. 1.6 10 ° 60-90 ° desktop to 0.30 5 ° 50 ° 85-140 ° - St. 0.30 to 0.40 10 ° 40 ° 80-130 ° St. .40 20 ° 30 ° 70-120 ° Permissible installation height wall lights should be listed in the technical specifications for specific types or groups of fixtures. Values ??protective corners in the lower hemisphere lamps for general lighting of residential premises shall not be less than: 30 ° - for hanging and ceiling lamps with fluorescent lamps, the values ??shown in Table. 5, - for desk lamps with fluorescent lamps and incandescent lamps. 2.2.5. Values ??protective corners, restricted areas of brightness and overall brightness is not set for fixtures intended: for ceremonial rooms at the height of installation of fixtures at least 3.2 m for the installation of light-scattering surface of the luminous ceiling, installation of construction elements, shielding the lamp, for installed in hallways and other rooms with a temporary stay of people, except for corridors in hospitals, for wall fixtures with fluorescent lamps for public premises, in the longitudinal plane - for lighting, light whose center is located at a distance of no more than 0,3 m from the wall, with horizontal arrangement of lines of lamps, as well as the location of the plane of the curved tubes parallel to the wall, in the transverse plane in the lower hemisphere - for lighting, light whose center is located at a distance of not more than 1,0 m from the floor, and for general lighting of residential premises: Ceilings, suspended, wall and floor - with incandescent lamps, wall and floor - with fluorescent lamps, for lamps, intended for residential, luminous surfaces that do not fall at work in the field of view, for decorative lighting. 2.2.6. The values ??of overall brightness of the illuminated surface of the suspension, ceiling and built-in fixtures with discharge lamps for general illumination of public premises within the zone limits of brightness shall be as specified in Table. 4. The value of overall brightness of the illuminated surface of the hanging and ceiling lamps for general lighting of premises with fluorescent lamps should be not more than 5000 cd/m2 brightness limit in the zone 60-90 °. 2.2.7. The values ??of overall brightness of the illuminated surface of the wall and floor lamps for general lighting of public areas with discharge lamps and lighting fixtures for general lighting public buildings with incandescent lamps should be installed in the standards or specifications for specific types or groups of fixtures. The value of overall brightness of the illuminated surface of the desk lamps for general lighting with fluorescent lamps and incandescent lamps should be not more than 2000 cd/m2 brightness limit in the zone specified in the table. 5. 2.2.4 - 2.2.7. (Revised edition, Alt. N 1, 2). 2.2.8. The values ??of overall brightness of the illuminated surface of the fixtures of the local and the combined illumination, measured at 90 ° in accordance with GOST 17677-82, should not be more than the value permissible overall brightness, cd/m2, calculated by the formula where L - the value of overall luminance of the Table. 6 cd/m2 - total luminous flux of lamps installed in the lamp, lumens; Ssv - projected area of ??the illuminated surface of the lamp on the vertical plane, m2; K - correction factor chosen according to Table. 7. Table 6: Light distribution class according to GOST 17677-82 overall brightness, cd/m2, no more for hanging and floor lamps for desktop, wall and is attached fixtures 4500 4000 N P 4000 3000 P 3000 2000 Table 7: How to install lighting correction factors for the distance of the luminous center lamp to the floor, m not more than 1.1 1.1-1.15 1.16-1.20 1.21-1.25 1.26-1.30 1.31-1.40 1.41-1.50 1.51 or more hanging, floor 1.00 1.05 1.15 1.25 1.30 1.35 Desktop, Wall, BUILT 1.00 1.15 1.35 1.55 For fixtures that have multiple individual lenses of the same shape and size, and Ssv determined for only one lens. If the shape, dimensions and materials of lenses lamp are different, and Ssv determine for each lens. 2.2.9. The values ??of overall brightness of the illuminated surface of the night-light at an angle of 90 ° should not exceed 500 cd/m2. 2.2.10. The efficiency of the lamps for general lighting for premises with discharge lamps shall not be less than indicated in the table. 8. The efficiency of the lamps for general lighting public spaces with all light sources except combined with a ventilation system and air conditioning must be specified in the technical specifications for specific types or groups of fixtures and shall not be less than indicated in the table. 8. The efficiency of the fixtures with svetotehnicheskimi schemes not listed in the Table. 8, must be at least 45%. May decrease efficiency compared with that indicated in Table. 8 is not more than 5% for lighting: a lens or shield grid of colored material, with curly fluorescent bulbs, with more than two fluorescent lamps, wall, floor, embedded systems, ceiling height of less than 100 mm with protective netting, with Louvres that creates a protective angle greater than 40 °; with two or more discharge lamps of high pressure. When several of these factors may decrease the total value of the efficiency of not more than 10%. The efficiency of the lighting fixtures with discharge lamps, equipped with shielding elements and having a security angle only in one plane, should be 5% higher than the values ??shown in Table. 8. Table 8: Light distribution class according to GOST 17677-82 Feature reflector protective (or defensive conditioned), the angle in the lower hemisphere efficiency,%, at least with a transparent protective glass with a lens or prelomlyatelem with Louvres or ring without optical and shielding elements of a lens and shielding elements or diffuser and prelomlyatelem P and O Mirror Up to 15 ° 65 55 60 70 - St. 15 ° 60 65 Diffuse St. 15 ° 50 50 60 50 90 ° - - H and Mirror Up to 15 ° 70 65 75 - St. 15 ° 65 60 70 15 ° 55 70 55 Diffuse St. 15 ° 60 55 65 50 90 ° - 60 - Up to 15 ° 70 75 60 Diffuse St. 15 ° 65 60 60 70 55 90 ° - - 60 P - 70 - - 80 - No reflector 15 ° - 15 ° St. 65 75 65 90 ° - - 2.2.11. The efficiency of the lamps for general lighting with incandescent lamps for residential premises shall not be less than indicated in the table. 9. Table 9 Types of lighting fixtures in the way of installation and material of the lens efficiency,% Hanging, wall, floor, table, ceiling: no lens and shielding elements 80 with a suspension of transparent silica glass or crystal 75 with a lens of transparent silica or crystal glass or transparent plastic, with pendants of clear plastic 70 with a lens of plastic film or a white, milky, of milk bill, opalescent or frosted lime glass, as well as of transparent silica glass, colored inks or lyustrovymi silicate enamels 60 with lenses made of colored silicate glass superimposed milky colored glass, colored plastics and films, fabrics, paper, and duplicate materials as well as the type of glasses in accordance with GOST 10036-75 50 with the shielding elements 50 may decrease the efficiency of not more than 10% - for lamps with additional shielding elements, a lens of color two-layer plastic; 5% - for ceiling and pendant fixtures with fully overlapped outlets, as well as mnogolampovyh ceiling lights. 02/02/1910, 2.2.11. (Revised edition, Alt. N 1, 2). 2.2.12. Efficiency is not standardized for light local and combined lighting, decorative lighting and night light exposure. 2.2.13. The illumination of the working surface, created a lamp or a combination of local lighting discharge lamps shall be not less than: 400 lux - at the operating level surface dimensions 0.85 X 0, 6 m for lighting drawing tables and 300 lux - at the operating level surface dimensions 0.4 X0 3 m to cover the desks, while working on a horizontal surface dimensions not less than 0,6 X0, 4 m, the illumination shall not be less than 100 lux. 200 lux - at the operating level surface dimensions not less than 0,4 X0, 3 m to cover the provision of short-visual work in a residential area, and for lamps with improved color reproduction (LTBTS, LTBTSTS, rings) - 150 lux. The specific size of the surface must be specified in the operational document in accordance with GOST 2.601-68. 300 lux - at the operating level surface dimensions of 0.3 X 0, 2 m for lighting desks odnolampovymi lamps with compact fluorescent bulbs, 500 lux - at the operating level surface 0,15 X0, 10 m for lighting objects distinguish very high accuracy, while Working on a flat surface with dimensions not less than 0,3 X0, 2 meters, the illumination shall be not less than 200 lux. 02/02/1912, 2.2.13. (Revised edition, Alt. N 2). 2.2.14. The illumination of the working surface, created a lamp or a combination of local lighting with incandescent lamps shall be not less than 100 lux within the circle diameter: 0,5 m - for wall, desktop, and is attached fixtures, 0,6 m - for hanging and floor lamps. 2.2.15. 2.3. 2.3.3. 2.4. 2.4.3. 11. 2.5. 2.5.2. 2.5.4. 2.5.5. 3. 3.2. 3.3. 3.4. 3.5. 4. 5. 6. 6.2. 6.3. 6.4. 6.5. 7. 8. 8.2. General specifications GOST 2.702-75 Unified system for design documentation. Rules for making electronic circuits with GOST 2.752-71 Unified system for design documentation. Graphical symbols in diagrams. Robot device GOST 2.755-87 Unified system for design documentation. Graphical symbols in electrical circuits. Device switching and contact connections GOST 2.756-76 * Unified system for design documentation. Graphical symbols in diagrams. Is often perceived electromechanical devices GOST 2.757-81 * Unified system for design documentation. Graphical symbols in diagrams. Elements of the switching field for switching systems GOST 2.758-81 Unified system for design documentation. Graphical symbols in diagrams. Signal Technology GOST 2.762-85 * Unified system for design documentation. Graphical symbols in electrical circuits. Frequencies and frequency bands for transmission systems GOST 2.763-85 * Unified system for design documentation. Graphical symbols in electrical circuits. Device with a pulse-code modulation GOST 2.764-86 Unified system for design documentation. Graphical symbols in electrical circuits. Integrated optoelectronic display elements GOST 2.768-90 Unified system for design documentation. Graphical symbols in diagrams.
GOST 8607-82 (ST SEV 3891-82) Group E83 STATE STANDARD OF THE USSR FOR LIGHTING FIXTURES residential and public buildings General specifications Luminaries for domestic and public interior lighting. General specifications OKP 34 6150 1934 6160 Effective date 01.01.1984 MEDIA INFORMATION 1. Developed and submitted by the Ministry of Electrical Industry of the USSR DEVELOPERS TN Siseykina (Leader), GS Sarychev, Dr. Sc. Sciences, BN Orlov, AV Ochkin; YB Eisenberg, Dr. Sc. Science; GN Undasynov, k.t.nauk 2. Approved and put into effect by Decision of the USSR State Committee on Standards of 09.11.82 N 4220 3. The standard is fully consistent ST SEV 3891-82 4. INSTEAD GOST 8607-74, GOST 11536-75 and GOST 14804-69 5. REFERENCE normative and technical documents Designation NTD, which was referenced paragraph number, sub-transfer, the application of GOST 2.601-68 2.2.2, 02/02/1913; 2.5.4, 3.2, 3.3, 3.5, 8.1 Standard 12.2.007.0-75 02.03 .1 GOST 7376-89 6.3.1.1; 6.3.2.1 GOST 7399-80 2.3.1, 02/04/1915; 04/02/1916 GOST 7933-89 6.3.1.1; 6.3.2.1 6.3.2.1 GOST 9142-90 GOST 10036-75 2.2.11; 6.3.1.1 6.3.1.1 GOST 10354-82 GOST 14254-80 GOST 15150-69 02.04.1915 2.4.1, 6.4; 6.5 GOST 17516-72 GOST 17557-88 2.4.3 2.4.9, 04/02/1910 GOST 17677-82 Chapeau, 1.1, 1.3, 2.2.1, 2.2.4, 2.2.8, 02.02.1910, 2.3.1, 2.4.2, 4/2/1915, 3.1, 4.1, 5.1, 6.1, 6.3, 7.1 GOST 21177-82 2.5.6 GOST 23216-78 6.3; 6.3.1.1; 6.4 GOST 23511-79 GOST 25516-82 2.5.6 02/04/1915 GOST 26092-84 Norms 15-78 2.5.6 04/02/1910 6. Validity extended until 1/1/1994 * Decree of the USSR State Standard 16.06.88 N 1843 _____________________ * Limiting the term of the removed protocol N 3-93 Interstate Council for Standardization, Metrology and Certification. (ICS N 5-6, 1993). 7. Reissue (September 1990) with variations in N 1, 2, 3, approved in October 1983 and September 1987, June 1988 (ICS 1-84, 12-87, 9-88) This standard applies to lamps with incandescent and discharge lamps for lighting of residential and public buildings which are produced by the economy and for export. The standard does not apply to lamps with individual power supplies, special medical, lighting and other theatrical scenes for photo, film and telesemok and television. Fixtures must meet the requirements of GOST 17677-82 and the requirements set forth in the relevant sections of this standard. (Revised edition, Alt. N 1, 2). 1. Classification 1.1. Classification fixtures - as per GOST 17677-82. 1.2. Classification of lamps for lighting of residential premises for the appointment is given in Table. 1. Table 1: Classification of lighting purpose lamps for general lighting (pendant, ceiling, wall, floor, table) for general lighting facilities Fixtures local lighting (table, floor, wall, pendant, is attached, built-in furniture) to ensure coverage of the working surface in accordance with the executed the visual work of the combined illumination lamps (pendant, wall, floor, table) have served as general lighting and local lighting, or both functions simultaneously Decorative lamps (table, wall) have served as an element of interior decoration lighting for orientation - nightlights (table, wall) To create the lighting necessary for orientation in a residential area in the nighttime lighting Spotlight (desktop, wall and is attached, recessed, ceiling, pendant, floor) to illuminate certain objects (Revised edition, Alt. N 1, 2). 1.3. Symbols of luminaries - as per GOST 17677-82. 2. SPECIFICATIONS 2.1. Lamps for residential premises shall be made in accordance with the requirements of this standard for technical documentation, duly approved. Fixtures for public buildings should be constructed in accordance with the requirements of this standard and technical requirements for specific types or groups of lamps to the technical documentation, duly approved. (Revised edition, Alt. N 2). 2.2. Light technical requirements 2.2.1. Light distribution class fixtures general, local and combined illumination of public premises should comply with GOST 17677-82 and indicated in the technical specifications for specific types or groups of fixtures. Type of curve intensity lamps for general lighting for public buildings should comply with GOST 17677-82 and indicated in the technical specifications for specific types or groups of fixtures. Light distribution class fixtures with incandescent and discharge lamps general, local and combined lighting of premises should comply with GOST 17677-82 and fitted visually to calculate the overall brightness. Type of curve intensity lamps for residential premises not specified. (Revised edition, Alt. N 1, 2). 2.2.2. Values ??protective corners and restricted areas of the local brightness lamps and combined lighting must comply with Table. 2 and the state: in any meridional plane - for Circular lamps; in the longitudinal and transverse, or only the transverse plane - for fixtures with two planes of symmetry. Table 2 Distance from the center of the light fixture to the floor, m Brightness limit area protective (or defensive conditioned) angle, at least in the lower hemisphere in the upper hemisphere to 1,1 inclusive. 85-125 ° 5 ° 35 ° St. 1,1 to 1.2 incl. 75-110 ° 15 ° 20 ° "1,2" 1,3 "65-95 ° 25 ° 5 °" 1,3 60-90 ° 30 ° - Notes: 1. The distance from the center of the light to the floor should be indicated in the operational document in accordance with GOST 2.601-68 lamps for residential premises, in the technical specifications for specific types or groups of fixtures - for public space, with distance from the optical center to the floor of mobile lighting fixtures for residential premises should be equal to the maximum allowable design in the position of lamps. 2. The bulb lights (except bulbs with mirrored dome of the bulb, decorative bulb and compact fluorescent lamps) should not extend beyond the plane of the upper or lower edge of the outlet of a lens or reflector. (Revised edition, Alt. N 1, 2, 3). 2.2.3. Values ??protective corners with night-light bulbs must meet the Table. 3. Table 3: How to install the lamp protective (or defensive conditioned) angle, at least in the lower hemisphere in the upper hemisphere Desktop 10 ° 90 ° Wall 30 ° (Revised edition, Alt. N 2). 2.2.4. Values ??protective corners and restricted areas of brightness lamps for general lighting public spaces in the lower hemisphere must comply with those in Table. 4 for the outboard, ceiling fixtures and built-in table. 5 - for wall and floor lamps. Table 4 Group rooms * Security (or conditional security), the angle in the transverse and longitudinal planes, at least Brightness limit area overall brightness, cd/m2, no more classes for light distribution according to GOST 17677-82 H P * In _________________________ Group premises are in a background application. January 1990 ° 0-90 ° 2000 2 2500 3000 3500 3 30 ° 60-90 ° 4500 5000 3500 * __________________________ * For ceiling and built-in lighting - no more than 5000 cd/m2. April 1990 ° 0-90 ° 4000 5000 5000 May 30 ° 60-90 ° 4500 * 5000 * __________________________ For ceilings and built-in lighting - no more than 5000 cd/m2. Table 5: How to install a light fixture Distance center lamp, m Protective (or contingent protection) angles in the transverse and longitudinal planes, at least Brightness limit area on the floor of the base area in the lower hemisphere in the upper hemisphere wall to 1.8 incl. - 30 ° 30 ° 60-120 ° St. 1,8 - 60-90 ° Floor Up to 1.0 incl. 10 ° 40 ° 80-130 ° from 1,0 to 1,3 inclusive. 20 ° 30 ° 70-120 ° St. 1,3 to 1.6 incl. 30 ° 20 ° 60-110 ° St. 1.6 10 ° 60-90 ° desktop to 0.30 5 ° 50 ° 85-140 ° - St. 0.30 to 0.40 10 ° 40 ° 80-130 ° St. .40 20 ° 30 ° 70-120 ° Permissible installation height wall lights should be listed in the technical specifications for specific types or groups of fixtures. Values ??protective corners in the lower hemisphere lamps for general lighting of residential premises shall not be less than: 30 ° - for hanging and ceiling lamps with fluorescent lamps, the values ??shown in Table. 5, - for desk lamps with fluorescent lamps and incandescent lamps. 2.2.5. Values ??protective corners, restricted areas of brightness and overall brightness is not set for fixtures intended: for ceremonial rooms at the height of installation of fixtures at least 3.2 m for the installation of light-scattering surface of the luminous ceiling, installation of construction elements, shielding the lamp, for installed in hallways and other rooms with a temporary stay of people, except for corridors in hospitals, for wall fixtures with fluorescent lamps for public premises, in the longitudinal plane - for lighting, light whose center is located at a distance of no more than 0,3 m from the wall, with horizontal arrangement of lines of lamps, as well as the location of the plane of the curved tubes parallel to the wall, in the transverse plane in the lower hemisphere - for lighting, light whose center is located at a distance of not more than 1,0 m from the floor, and for general lighting of residential premises: Ceilings, suspended, wall and floor - with incandescent lamps, wall and floor - with fluorescent lamps, for lamps, intended for residential, luminous surfaces that do not fall at work in the field of view, for decorative lighting. 2.2.6. The values ??of overall brightness of the illuminated surface of the suspension, ceiling and built-in fixtures with discharge lamps for general illumination of public premises within the zone limits of brightness shall be as specified in Table. 4. The value of overall brightness of the illuminated surface of the hanging and ceiling lamps for general lighting of premises with fluorescent lamps should be not more than 5000 cd/m2 brightness limit in the zone 60-90 °. 2.2.7. The values ??of overall brightness of the illuminated surface of the wall and floor lamps for general lighting of public areas with discharge lamps and lighting fixtures for general lighting public buildings with incandescent lamps should be installed in the standards or specifications for specific types or groups of fixtures. The value of overall brightness of the illuminated surface of the desk lamps for general lighting with fluorescent lamps and incandescent lamps should be not more than 2000 cd/m2 brightness limit in the zone specified in the table. 5. 2.2.4 - 2.2.7. (Revised edition, Alt. N 1, 2). 2.2.8. The values ??of overall brightness of the illuminated surface of the fixtures of the local and the combined illumination, measured at 90 ° in accordance with GOST 17677-82, should not be more than the value permissible overall brightness, cd/m2, calculated by the formula where L - the value of overall luminance of the Table. 6 cd/m2 - total luminous flux of lamps installed in the lamp, lumens; Ssv - projected area of ??the illuminated surface of the lamp on the vertical plane, m2; K - correction factor chosen according to Table. 7. Table 6: Light distribution class according to GOST 17677-82 overall brightness, cd/m2, no more for hanging and floor lamps for desktop, wall and is attached fixtures 4500 4000 N P 4000 3000 P 3000 2000 Table 7: How to install lighting correction factors for the distance of the luminous center lamp to the floor, m not more than 1.1 1.1-1.15 1.16-1.20 1.21-1.25 1.26-1.30 1.31-1.40 1.41-1.50 1.51 or more hanging, floor 1.00 1.05 1.15 1.25 1.30 1.35 Desktop, Wall, BUILT 1.00 1.15 1.35 1.55 For fixtures that have multiple individual lenses of the same shape and size, and Ssv determined for only one lens. If the shape, dimensions and materials of lenses lamp are different, and Ssv determine for each lens. 2.2.9. The values ??of overall brightness of the illuminated surface of the night-light at an angle of 90 ° should not exceed 500 cd/m2. 2.2.10. The efficiency of the lamps for general lighting for premises with discharge lamps shall not be less than indicated in the table. 8. The efficiency of the lamps for general lighting public spaces with all light sources except combined with a ventilation system and air conditioning must be specified in the technical specifications for specific types or groups of fixtures and shall not be less than indicated in the table. 8. The efficiency of the fixtures with svetotehnicheskimi schemes not listed in the Table. 8, must be at least 45%. May decrease efficiency compared with that indicated in Table. 8 is not more than 5% for lighting: a lens or shield grid of colored material, with curly fluorescent bulbs, with more than two fluorescent lamps, wall, floor, embedded systems, ceiling height of less than 100 mm with protective netting, with Louvres that creates a protective angle greater than 40 °; with two or more discharge lamps of high pressure. When several of these factors may decrease the total value of the efficiency of not more than 10%. The efficiency of the lighting fixtures with discharge lamps, equipped with shielding elements and having a security angle only in one plane, should be 5% higher than the values ??shown in Table. 8. Table 8: Light distribution class according to GOST 17677-82 Feature reflector protective (or defensive conditioned), the angle in the lower hemisphere efficiency,%, at least with a transparent protective glass with a lens or prelomlyatelem with Louvres or ring without optical and shielding elements of a lens and shielding elements or diffuser and prelomlyatelem P and O Mirror Up to 15 ° 65 55 60 70 - St. 15 ° 60 65 Diffuse St. 15 ° 50 50 60 50 90 ° - - H and Mirror Up to 15 ° 70 65 75 - St. 15 ° 65 60 70 15 ° 55 70 55 Diffuse St. 15 ° 60 55 65 50 90 ° - 60 - Up to 15 ° 70 75 60 Diffuse St. 15 ° 65 60 60 70 55 90 ° - - 60 P - 70 - - 80 - No reflector 15 ° - 15 ° St. 65 75 65 90 ° - - 2.2.11. The efficiency of the lamps for general lighting with incandescent lamps for residential premises shall not be less than indicated in the table. 9. Table 9 Types of lighting fixtures in the way of installation and material of the lens efficiency,% Hanging, wall, floor, table, ceiling: no lens and shielding elements 80 with a suspension of transparent silica glass or crystal 75 with a lens of transparent silica or crystal glass or transparent plastic, with pendants of clear plastic 70 with a lens of plastic film or a white, milky, of milk bill, opalescent or frosted lime glass, as well as of transparent silica glass, colored inks or lyustrovymi silicate enamels 60 with lenses made of colored silicate glass superimposed milky colored glass, colored plastics and films, fabrics, paper, and duplicate materials as well as the type of glasses in accordance with GOST 10036-75 50 with the shielding elements 50 may decrease the efficiency of not more than 10% - for lamps with additional shielding elements, a lens of color two-layer plastic; 5% - for ceiling and pendant fixtures with fully overlapped outlets, as well as mnogolampovyh ceiling lights. 02/02/1910, 2.2.11. (Revised edition, Alt. N 1, 2). 2.2.12. Efficiency is not standardized for light local and combined lighting, decorative lighting and night light exposure. 2.2.13. The illumination of the working surface, created a lamp or a combination of local lighting discharge lamps shall be not less than: 400 lux - at the operating level surface dimensions 0.85 X 0, 6 m for lighting drawing tables and 300 lux - at the operating level surface dimensions 0.4 X0 3 m to cover the desks, while working on a horizontal surface dimensions not less than 0,6 X0, 4 m, the illumination shall not be less than 100 lux. 200 lux - at the operating level surface dimensions not less than 0,4 X0, 3 m to cover the provision of short-visual work in a residential area, and for lamps with improved color reproduction (LTBTS, LTBTSTS, rings) - 150 lux. The specific size of the surface must be specified in the operational document in accordance with GOST 2.601-68. 300 lux - at the operating level surface dimensions of 0.3 X 0, 2 m for lighting desks odnolampovymi lamps with compact fluorescent bulbs, 500 lux - at the operating level surface 0,15 X0, 10 m for lighting objects distinguish very high accuracy, while Working on a flat surface with dimensions not less than 0,3 X0, 2 meters, the illumination shall be not less than 200 lux. 02/02/1912, 2.2.13. (Revised edition, Alt. N 2). 2.2.14. The illumination of the working surface, created a lamp or a combination of local lighting with incandescent lamps shall be not less than 100 lux within the circle diameter: 0,5 m - for wall, desktop, and is attached fixtures, 0,6 m - for hanging and floor lamps. 2.2.15. The distance from the center of the light fixture to a working horizontal surface must be at least 0,25 m, while the moving lights to create light at the working level surface in accordance with sub. 02.02.1913 and 02.02.1914 in at least one of the possible positions. The control wheel or surface should be placed on a horizontal plane at a height of 0,8 m from the floor. (Revised edition, Alt. N 2). 2.3. Electrical requirements 2.3.1. Fixtures shall be made protection classes I, II or III according to GOST 12.2.007.0-75. Table and floor lamps have to be manufactured protection class II. Fixtures protection class II, should have double or reinforced insulation, which must be provided: a complete set of patch cords in accordance with GOST 7399-89, having at the end of the pressure-tested with the plug wire, resistance and electrical insulation resistance according to GOST 17677-82; degree of protection against contact with live parts in accordance with GOST 17677-82. Protection class of fixtures for public buildings must be specified in the technical specifications for specific types or groups of fixtures. Allowed to produce suspended, ceiling and wall fixtures for residential protection class O. (Revised edition, Alt. N 1, 2). 2.3.2. The design of suspension and ceiling luminaires of protection class 0 shall provide electrical isolation of the lamp from the ceiling hook. Allowed to isolate the bracket hanging from the lamp. The requirement does not apply to fixtures that are suspended on the cord. Allowed lighting equipment of protection class II products that are not complying with the requirements of this class of protection, if the whole lamp complies with protection class II. 2.3.3. The total power consumed by the lamps for residential premises, must not exceed: 550 Watts - Lamp for general lighting, 180 watts - for a combined lamp lighting, 150 watts - for the light, local illumination, the exposure and decorative, and 25 watts - for a nightlight. In this case, the unit light source power must not exceed: 150 watts - for the light of general, local and combined lighting and 100 watts - for the exposure lamp, and for lamps with halogen bulbs no more than 150 watts, 60 watts - for decorative lighting; 25 watts - for a nightlight. (Introduced in addition, Mod. N 2). 2.4. Requirements for construction 2.4.1. Fixtures must meet climatic design UHL or 0 category 4 according to GOST 15150-69. Climatic version 0 by GOST 15150-69 for export. 2.4.2. Lamps must have a degree of protection according to GOST 17677-82 is not below: IP20 or 2'0 - fixtures for public buildings; IP20 - lamps for residential premises; IP21 - santehkabiny for residential and public buildings. Higher degree of protection fixtures for public buildings should be reported in the technical specifications for certain types or groups of fixtures. 2.4.3. Mechanical strength of fixtures must comply with the group is M1 in accordance with GOST 17516-72. The requirement does not apply to lamps for residential premises. 2.4.4. The design of abutting fixtures with two or more gas-discharge lamps shall be capable of laying eight wires group lines-section of 4,0 mm2, while the distance between the beams and wires of the working emergency lighting shall be not less than 20 mm in the light beams or wires must be separated by a partition of insulating material. In odnolampovyh abutting fixtures must be capable of laying at least four wires cross group lines up to 2,5 mm2. 2.4.5. For internal mounting fixtures should be used wires of not less than 0.5 mm2. 2.4.6. For decorative lamps, in which space for wiring is limited, is supposed to apply internal wires with nominal cross section of 0.35 mm2 conductor and insulation thickness of 0,5 mm. (Revised edition, Alt. N 2). 2.4.7. Allowed onto the wires internal mounting of valves and lining them outside only for lighting the degree of protection IP20 and 2'0. These wires must be secured so that during normal operation were excluded from being damaged and does not affect marketability lamp. 2.4.8. In mnogolampovyh fixtures with the inclusion of a group of lamps common mounting wire should be blue or should be marked in blue. Lamps for residential premises with the number of lamps for more than three must have an electrical circuit to turn on all lamps, or some of them. (Revised edition, Alt. N 2). 2.4.9. For connection of stationary lights to the mains should be provided for electrical connectors or terminal blocks in accordance with GOST 17557-88, or other terminals, providing connection of copper, alyumomednyh and aluminum wires up to: 2,5 mm2 - for lamps for residential premises, 4, 0 mm2 - for lighting for public spaces. This requirement does not apply to the hanging lamps for residential premises, other than lighting fixtures, are exported. (Revised edition, Alt. N 1, 2). 2.4.10. Ceiling height should be no less than 70 mm, have an internal volume of less than 87 cm3, and provide the possibility to hook her probation in accordance with GOST 26092-84, the stock aluminum network of conductors 2.5 mm2 minimum length of 150 mm and three-pin terminal block for GOST 17557-88. (Revised edition, Alt. N 2). 04/02/1911 - 02/04/1913. (Deleted, Mod. N 2). 02/04/1914. The sound level on a scale of A fixtures with discharge lamps at a distance of 1 m from the external circuit must be less than indicated in the table. 11. Table 11: Scope fixtures Sound Level A-weighted, dB Chamber of hospitals and sanatoriums 22.0 Group and bedrooms of children's institutions, operating, dressings, reception, treatment and diagnostic rooms in hospitals, residential premises 25.0 Classes, Training offices and classrooms in schools, universities and polytechnics, engineering, drafting and typing offices, reading rooms, laboratories, classrooms, study rooms, barbershops 30.0 Gym and game room, a room of teachers, the halls of banks, shopping and dining rooms, assembly and visual halls, lobbies of theaters, cultural centers, clubs, cinemas and other public places 35.0 (amended edition, Alt. N 2). 02/04/1915. Table and floor lamps for residential and public buildings, as well as wall-mounted, recessed lighting and is attached to dwellings should have: Switch to GOST 25516-82 or other normative and technical documentation on the current 1 A is allowed to use dimmers or touch controls light on the current not less than 0,3 A and manufacturer agreed with the customer embedded in the furniture fixtures without the breaker connecting cord in accordance with GOST 7399-80 or other normative and technical documentation with a transverse cross-section not less than indicated in the Table. 12, for outdoor lighting - not less than 0.75 mm2. Table 12 mm2, the total current value, A cross section of tendon at a degree of protection in accordance with GOST 14254-80 or GOST 17677-82 IP20 and IP21 on the 2'0 and above ? 3 1.0 0.50> 3 0.75 Connecting cord should have at the end of the plug, pressure-tested, together with a cord. The length of the cord from the place of its release on the lamp, including the plug, must be at least: 1,5 m - for desktop, wall, embedded systems and is attached fixtures; 3,0 m - for floor lamps, 2,0 m - for lighting shipped for export. Wall Lamps local lighting for public buildings should have the switch on the current no less than 1 A. Non-adherence to the network wall lights for santehkabiny accommodation with the terminal block. (Revised edition, Alt. N 2). 2.4.16. Lamps with incandescent lamps, suspended from cords and chains must have a cord length (from bullets) at least: 0,6 or 0,9 m - for lamps for general lighting, 1,5 m - for lighting and local lighting combined. Places of joining the cable to wiring products in the lamp must be protected from tension. (Revised edition, Alt. N 2). 2.5. Lifespan 2.5.1. The service life of lamps for residential premises shall not be less: 8 years - for lamps incorporating lenses of silicate glass and pendants made of crystal glass, 6 years - for the remaining fixtures. 2.5.2. The service life of lamps for public buildings must be at least 10 years. 2.5.1, 2.5.2. (Revised edition, Alt. N 2). 2.5.3. Shelf life lamps up to commissioning should be: 1 year - for illumination of public premises, 1,5 years - for the lighting of residential premises. (Revised edition, Alt. N 3). 2.5.4. Indicators of energy (power and number of lights) and indicators of material (mass fixtures) must be specified: in technical terms in light of specific types or groups for public spaces; in the operational document in accordance with GOST 2.601-68 - for lighting for residential applications. (Revised edition, Alt. N 2). 2.5.5. (Deleted, Mod. N 3). 2.5.6. Levels of interference caused at work lamps should not exceed the values ??established: in GOST 23511-79 - in the operation of light fixtures in living rooms or connecting them to the power grid dwellings; in GOST 21177-82 - for lamps with fluorescent lamps, the Norms 15-78 - during the operation of light fixtures in the locations of service radioprinimayuschih devices. (Introduced in addition, Mod. N 3). 3. COMPLETE 3.1. Set of lights should comply with GOST 17677-82. 3.2. Fixtures for public buildings should be accompanied by a passport or instruction manual GOST 2.601-68 in quantities of 1 pc. for every 50 lights that are sent to one shipping document. If the number of fixtures in the party less than 50, then applied a passport or an instruction manual. 3.3. Lamps for residential premises must be accompanied by artistically designed operational documents in accordance with GOST 2.601-68. Operating document must be supplied in quantities of 1 pc. for each lamp. Type of operating the document is determined by the manufacturer. (Revised edition, Alt. N 2). 3.4. Lamps with fluorescent lamps for residential premises should be equipped with lamps and starters. 3.5. The set of lamps for residential premises with pendants made of transparent silica glass or crystal should additionally include spare suspension. Number of spare suspension shall be indicated in the operational document in accordance with GOST 2.601-68. (Revised edition, Alt. N 2). 4. RULES OF ACCEPTANCE 4.1. Acceptance luminaries - as per GOST 17677-82. 5. TEST METHODS 5.1. Methods of test fixtures - as per GOST 17677-82. 6. Labelling, packaging, transportation and storage 6.1. Marking lights should comply with GOST 17677-82. 6.2. The marking on the lamps for residential premises made in any way. Allowed the marking on the label affixed in any manner to the lamp. (Revised edition, Alt. N 2). 6.3. Packing fixtures should comply with GOST 17677-82 and GOST 23216-78. 6.3.1. Inner packing fixtures for residential 6.3.1.1. Lamps for residential premises should be wrapped in packing paper and packed in consumer packaging - individual boxes of boxboard in accordance with GOST 7933-89 or paperboard other brands with similar characteristics of corrugated cardboard in accordance with GOST 7376-84 or gofroplasta. Allowed to be used as consumer packaging: shrink film, bags made of polyethylene film in accordance with GOST 10354-82 thickness of not less than 0,15 mm - other than lighting with pendants made of crystal or silica glass. In this light should not be wrapped in paper, packaging paper by fixing it on the lamp in any way or blankets made of polyethylene film in accordance with GOST 10354-82 thickness of not less than 0,15 mm - floor lamps are longer than 1 m. Allowed: packing lenses separately from the mixer, using as a consumer packaging shrink films, bags made of polyethylene film in accordance with GOST 10354-82 thickness of not less than 0,15 mm, or grid bezuzlovoy polyethylene, or a protective cuff of a double-layer corrugated cardboard according to GOST 7376-84; not wrap in paper luminaries with lenses of film material or fabric. In this case, should be applied to cases or bags made of polyethylene film in accordance with GOST 10354-82 thickness of not less than 0,15 mm; not wrap in paper lamps, placed in individual boxes to ensure the safety of lamps from mechanical damage, as well as lamps, placed in a box with special walls, or having other ways to protect against mechanical damage during transportation, packing group in accordance with GOST 23216-78 lamps for residential premises for the supply of nonmarket customers. In this case, the lenses of a silicate glass can have a package in accordance with GOST 10036-75. Consumer packaging must be artistically designed markings showing: the word "light", the symbol lamp or conventional name, manufacturer's name or trademark; article list price, retail price. (Revised edition, Alt. N 2, 3). 6.3.2. Shipping containers fixtures for residential 6.3.2.1. The main type of transport container lamps for residential premises should be cargo containers. You can use cardboard boxes to GOST 9142-90, GOST 7933-89 wooden boxes or boxes made of corrugated cardboard in accordance with GOST 7376-84. During transportation of packages packages they must comply with the Rules of carriage of goods, operating on each type of transport. Dimensions and mass transport packages should be specified in the technical documentation. (Revised edition, Alt. N 2, 3). 6.4. Transportation conditions lamps in part the impact of climatic factors in the external environment must match the storage group 2 according to GOST 15150-69, in part the impact of mechanical factors - group A according to GOST 23216-78. 6.5. Storage conditions lamps must comply with Group 2 in accordance with GOST 15150-69. 7. MANUFACTURER'S WARRANTIES 7.1. Manufacturer's warranty - GOST 17677-82. 8. OPERATING INSTRUCTIONS 8.1. Operation of lamps should be carried out in accordance with the requirements: Passport or instruction in accordance with GOST 2.601-68 - fixtures for public spaces; operational documents in accordance with GOST 2.601-68 - lamps for residential premises. 8.2. Lamps with incandescent lamps for residential premises may be used with microprocessor-based automation. Sec. 8 (Introduced in addition, Mod. N 2). ANNEX Reference Group premises Scope lighting a Group and bedrooms of children's institutions, hospital wards 2 Operating, dressings, reception, treatment and diagnostic rooms in hospitals, classrooms and classrooms in schools 3 Rooms of teachers, classrooms, training rooms and auditoriums in universities and polytechnics, engineering, drafting and typing offices, reading rooms, laboratories, classrooms, study rooms, barbershops 4 Gym and Game Rooms 5 Rooms banks, shopping and dining rooms, assembly, visual rooms, lobbies of theaters, cultural centers, clubs and cinema halls, laboratories, classrooms, study rooms, barbershops 4 Gym and Game Rooms 5 Rooms banks, shopping and dining rooms, assembly, visual rooms, lobbies of theaters, cultural centers, clubs and cinemas Posted 06/27/2008 GOST on "Electricity, lighting , security system, "GOST 15597-82 Fixtures for industrial buildings. General specifications GOST 2.702-75 Unified system for design documentation. Rules for making electronic circuits with GOST 2.752-71 Unified system for design documentation. Graphical symbols in diagrams. Robot device GOST 2.755-87 Unified system for design documentation. Graphical symbols in electrical circuits. Device switching and contact connections GOST 2.756-76 * Unified system for design documentation. Graphical symbols in diagrams. Is often perceived electromechanical devices GOST 2.757-81 * Unified system for design documentation. Graphical symbols in diagrams. Elements of the switching field for switching systems GOST 2.758-81 Unified system for design documentation. Graphical symbols in diagrams. Signal Technology GOST 2.762-85 * Unified system for design documentation. Graphical symbols in electrical circuits. Frequencies and frequency bands for transmission systems GOST 2.763-85 * Unified system for design documentation. Graphical symbols in electrical circuits. Device with a pulse-code modulation GOST 2.764-86 Unified system for design documentation. Graphical symbols in electrical circuits. Integrated optoelectronic display elements GOST 2.768-90 Unified system for design documentation. Graphical symbols in diagrams.
No comments:
Post a Comment